AAF E2 Olympia Image for Octagon SF-1018 Twin HD Linux
AAF E2 Olympia Image for Octagon SF-1018 Twin HD Linux
Original Image for Atevio 7000 USB clon Octagon SF-1018
Image Info
AAF Olympic Image Atevio 7000 USB
Changelog since last winter AAF Image Release:
SH4 Duckbox Project git rev281:
+ Driver optimizations (thanks to the TDT)
HD DVD Player Skin fix
+ Kernel optimization
E2 + Various minor bug fixes
+ Player behavior improved
Timeshift + Start improving
+ Update kernel config
Audioplayer mit Playlistsupport
This image has been resized. Click this bar to view the full image. The original image is sized 960x540.
Radioplayer mit Playlistsupport
This image has been resized. Click this bar to view the full image. The original image is sized 960x540.
AAF: (based on flash M2207)
+ Olympic infobar Skin
+ Update Auto Resolution Plug
+ New V13 station list
+ Playlist support in Media Center
+ WebradioFS green screen fix
+ Various bug fixes
+ When sound problems can be placed on the AAF panel nosync Yes
Bootvideo
Known issues:
- Sometimes, after the switch zapping no sound (sound or channel helps)
- After prolonged use it can happen that the sound stutters help switch ()
- The AGC indicator is always at 0%
- DTS downmix does not go
Thanks to Team Ducktales for the great base image and all have been tested and will allow that image.
If no boot image is displayed:
-> AAF Panel -> Settings -> Startup -> General -> Boat Resolution -> High
Shutdownvideo:
AAF Olympic Atevio 7000
Requirements:
To get E2 to Atevio 7000 required her to the following:
- A null modem cable (if PC / laptop no longer has access USB2Serial adapter works but unfortunately not all - if you saw Him gegenenfalls exchange extra worried)
- Network cable (for direct connection to PC / laptop using a crossover)
- AAF Recovery Tool 1.5 or higher
- E2 Flash Image / E2 USB Image
- Should be port 69 for the AAF recovery tool to be activated (in case of doubt (Windows) disable firewall during installation)
New Boot Loader Flashing:
1. AAF recovery tool to install
2. Box off and network and connect a null modem cable to the PC / laptop
3. AAF recovery tool to start and click on connect
4. Switch Box - the boot process should be interrupted if not see 4.1
4.1 It may happen in rare cases that the AAF recovery tool fails to interrupt the boot process. In this case, you need a terminal program such as Windows HyperTerminal or Putty
Putty / Hayperterminal set as in the image and click Apply.
Uobičajeno AAF E2 Olympia Image for Octagon SF-1018 Twin HD Linux
AAF E2 Olympia Image for Octagon SF-1018 Twin HD Linux
Original Image for Atevio 7000 USB clon Octagon SF-1018
Image Info
AAF Olympic Image Atevio 7000 USB
Changelog since last winter AAF Image Release:
SH4 Duckbox Project git rev281:
+ Driver optimizations (thanks to the TDT)
HD DVD Player Skin fix
+ Kernel optimization
E2 + Various minor bug fixes
+ Player behavior improved
Timeshift + Start improving
+ Update kernel config
Audioplayer mit Playlistsupport
This image has been resized. Click this bar to view the full image. The original image is sized 960x540.
Radioplayer mit Playlistsupport
This image has been resized. Click this bar to view the full image. The original image is sized 960x540.
AAF: (based on flash M2207)
+ Olympic infobar Skin
+ Update Auto Resolution Plug
+ New V13 station list
+ Playlist support in Media Center
+ WebradioFS green screen fix
+ Various bug fixes
+ When sound problems can be placed on the AAF panel nosync Yes
Bootvideo:
Known issues:
- Sometimes, after the switch zapping no sound (sound or channel helps)
- After prolonged use it can happen that the sound stutters help switch ()
- The AGC indicator is always at 0%
- DTS downmix does not go
Thanks to Team Ducktales for the great base image and all have been tested and will allow that image.
If no boot image is displayed:
-> AAF Panel -> Settings -> Startup -> General -> Boat Resolution -> High
Shutdownvideo:
AAF Olympic Atevio 7000
Requirements:
To get E2 to Atevio 7000 required her to the following:
- A null modem cable (if PC / laptop no longer has access USB2Serial adapter works but unfortunately not all - if you saw Him gegenenfalls exchange extra worried)
- Network cable (for direct connection to PC / laptop using a crossover)
- AAF Recovery Tool 1.5 or higher
- E2 Flash Image / E2 USB Image
- Should be port 69 for the AAF recovery tool to be activated (in case of doubt (Windows) disable firewall during installation)
New Boot Loader Flashing:
1. AAF recovery tool to install
2. Box off and network and connect a null modem cable to the PC / laptop
3. AAF recovery tool to start and click on connect
4. Switch Box - the boot process should be interrupted if not see 4.1
4.1 It may happen in rare cases that the AAF recovery tool fails to interrupt the boot process. In this case, you need a terminal program such as Windows HyperTerminal or Putty
Putty / Hayperterminal set as in the image and click Apply.
Now turn right after repeatedly pressing the spacebar until the output looks like this:
This image has been resized. Click this bar to view the full image. The original image is sized 667x420.
That was then but already - now could end her Putty, start AAF recovery tool and click on connect.
5. Network parameters and click on "Save." (The Atevio box must be in the same network as the PC are!)
Who wants to change its MAC address should restart after changing the box so that the new address will be accepted.
This image has been resized. Click this bar to view the full image. The original image is sized 764x59
6. Well above the tab "Maxi submarine Install" and click click "Install Maxi submarine rev 0.5.
This image has been resized. Click this bar to view the full image. The original image is sized 764x59
- Should not fold the installation please check Check (Windows) or firewall settings (Windows-off) firewall temporarily.
This image has been resized. Click this bar to view the full image. The original image is sized 764x594.
7. Box shut down and switch before connecting again with the "connect"
- Now click on the tab Maxi bootdesc Defaults
- On the Set Default (click If a hard disk installed before selecting "Internal SATA)
This image has been resized. Click this bar to view the full image. The original image is sized 764x59
Those who also still want to pick the default boot it from version 1.6 can now do the bottom too.
- For safety, the network parameters are all right in there we go again
on the first page of "Settings" and click "save"
8. Thus, the new boot loader would instlliert - now there are 2 ways to bring the box E2
9. E2 install the Flash
Who wants to test E2 on the stick reads on to point 10.
- Switch off the box
- Start AAF recovery tool and click on connect. (should not go to connect, see point 4.1)
- Click on the tab at the top Flash Image E2
- On "..." and click to select the image, memory E2
- Click on Flash E2 and loading - Receiver not turn
This image has been resized. Click this bar to view the full image. The original image is sized 764x59
- E2 in Flash is now done and will start at the next reboot automatically.
This image has been resized. Click this bar to view the full image. The original image is sized 96
9.1 The way back to the original image
If you the actual beta of E2 in the flash still not convinced you can, of course, any time back to the original
- Switch off the box and connects the network, and null modem cable to the PC / laptop
- AAF Recovery Tool Start, click connect and switch the receiver
(should stop the boot-time simply does not work when "E2 flash in the display is fast with the arrow keys to select on the remote control, the normal flash, resulting in a Softreboot and Recovery Tool connectet safe)
- Click on the tab "Recovery Image" and "Start"
This image has been resized. Click this bar to view the full image. The original image is sized 764x594.
Original 9.2 bootloader install
If anyone wants to have again the old bootloader from the factory setting, this is not a big problem
- Switch off the box and connect a null modem cable and network cable to the PC
- AAF Recovery Tool Start, click connect and switch the receiver
(should stop the boot-time simply does not work when "E2 flash in the display is fast with the arrow keys to select on the remote control, the normal flash, resulting in a Softreboot and Recovery Tool connectet safe)
- Click on the tab "Original U-boot Install" and "Install the original U-Boot 1.1.2 Click" - done!
This image has been resized. Click this bar to view the full image. The original image is sized 764x594.
If an error occurs Ping - the network settings can be written again in the bootloader and reboot.
10. E2 on USB stick install
Prerequisite:
- Installed Maxiboot 0.5 with default set bootargs
- USB Flash Drive
- AAF Maxiboot installer Atevio 7000
USB stick set up and install image
Install - AAF Maxiboot installer Atevio 7000
- Start AAF Maxiboot Installer
- Enter network parameters
- Receiver software start (if not already running)
- Click on connect
This image has been resized. Click this bar to view the full image. The original image is sized 962x311.
- By clicking the right mouse button on the stick and "Partinioning"
This image has been resized. Click this bar to view the full image. The original image is sized 954x292.
- Now create the desired partitions
MINI1
MINI2
...
SWAP (for flash image)
- Now click with the right mouse button on the partition on which the image is to be installed and click "Mount"
(If the drive has already been created, it may be among the E2, the partitions have been mounted)
This image has been resized. Click this bar to view the full image. The original image is sized 960x336
Then again, right-click the partition and on the "Install Image"
This image has been resized. Click this bar to view the full image. The original image is sized 926x
Bestätitgen warning
- Choose to install Image
- Enter name
- Wait
This image has been resized. Click this bar to view the full image. The original image is sized 962x376
- Finish can now turn directly to the desired image with the remote control (up / down are) elected and if it should be standard press the button with the red circle.
In order to have a clue where the partition is to be found
Here 2 examples:
Internal SATA HDD available:
sdb1 = S-USB1
No hard drive connected:
sda1 = USB1
Please also note
- Setting up and remove after installing a null modem cable to the receiver for cable plugged in to boot the receiver only when the PC is on.
- Provide for sound through HDMI into the A / V settings SPDIF as the audio source
E2 The image is still at a very early beta stage so that you may experience some problems.
download image:
You are not allowed to view links.
Register or
Login
