« previous next »
Pages: [1]   Go Down

Author Topic: Vantage Firmware  (Read 10690 times)

0 Members and 1 Guest are viewing this topic.

Offline labud

  • Administrator
  • Hero Member
  • *****
  • Posts: 9026
Vantage Firmware
« on: September 23, 2009, 08:17:19 PM »
Vantage Firmware


Vantage X200ér Serie.

README

23.09.2009 Version 063AOP

* Problem bei Multifeedkanälen behoben.
Logged
-----------------------------------------------








UNAUTHORIZED DECODING OF ENCRYPTED SIGNALS FROM EITHER DOMESTIC OR FOREIGN PROVIDERS IS AGAINST THE LAW !!!
INFORMATION CONTAINED IN MY POSTS ["C/P FROM ANOTHER SITE"] ARE FOR LEARNING AND EDUCATIONAL PURPOSES ONLY !!!
PLEASE, DO NOT SEND ME PRIVATE MESSAGES WITH TECHNICAL QUESTIONS, USE FORUM FOR IT !!!

Offline labud

  • Administrator
  • Hero Member
  • *****
  • Posts: 9026
Re: Vantage Firmware
« Reply #1 on: December 01, 2009, 11:47:39 AM »
New Final Software 2.57 T-O 011209


New Features:
1. Dolby Digital Plus support
2. CI option to choose the Entschlüsselungsart (Twin) devices.
The menu / multimedia / PVR settings, there is a new option "CI Dual Recording".
Is the option to "Off" is the old engine for CI uses pictures.
Does it mean the encrypted transmissions can only be seen and recorded on a transponder.
The recordings will be stored unencrypted.
The transponder overall record scrambled channels is not possible.
If the option to "On" then the new engine is active, which means
transponder can be made to record scrambled channels overall.
The recordings are encrypted on the disk

Improvements:
- Fixed problem when the time synchronization channel was active, and many recordings were not started is fixed.
- The general stability of the CI detection was improved.
- Crashes in "TV System NTSC" setting fixed.
- General Timer problems fixed.
- Timer recording problems Unicable fixed
(Background image was removed for Unicable that exclude only a temporary solution to defective recordings. It is
worked out that a background recording again in the future is possible)
- Canal Digital Cam Fixed
- Fixed error in the grips with the language
- Update channel lists for Astra
Logged
-----------------------------------------------








UNAUTHORIZED DECODING OF ENCRYPTED SIGNALS FROM EITHER DOMESTIC OR FOREIGN PROVIDERS IS AGAINST THE LAW !!!
INFORMATION CONTAINED IN MY POSTS ["C/P FROM ANOTHER SITE"] ARE FOR LEARNING AND EDUCATIONAL PURPOSES ONLY !!!
PLEASE, DO NOT SEND ME PRIVATE MESSAGES WITH TECHNICAL QUESTIONS, USE FORUM FOR IT !!!

Offline elcardinal74

  • Hero Member
  • *****
  • Posts: 2056
Re: Vantage Firmware
« Reply #2 on: December 03, 2009, 08:05:32 PM »
New 25501 Fixed for Vantage HD Series 03.12.2009 mit E*U_Fix_3!

New:

- Fixed card reading N*S

Viel Spaß damit
Logged


Offline elcardinal74

  • Hero Member
  • *****
  • Posts: 2056
Re: Vantage Firmware
« Reply #3 on: December 03, 2009, 09:00:19 PM »
New 25701 Firmware for Vantage HD Series 03.12.2009 mit E*U!

New:

- Fixed card reading NDS

Viel Spaß damit
Logged


Offline antox

  • Ferengi
  • Global Moderator
  • Hero Member
  • *****
  • Posts: 16798
Re: Vantage Firmware
« Reply #4 on: December 10, 2009, 11:49:07 PM »
EMU Firmware 025701 for Vantage HD

Allegedly, with this firmware a bit of running HD + Card
be possible without the legacy module.
However, it will not run properly stable.
A start would be the same.


Soft contain old today.
So far everything Prima. Runs flawlessly with Sky V13 card.

Attention:
If update is from 025501, comes at the beginning of a message that just plays for the same software.
This is probably a mistake.
So confirm with YES.
After the update, you can see in the system information,
that it is really a question of 025701

Logged

Offline elcardinal74

  • Hero Member
  • *****
  • Posts: 2056
Re: Vantage Firmware
« Reply #5 on: December 12, 2009, 11:38:48 PM »
Vantage 025501 HD+Card

New:
HD+ Card ok
Logged


Offline labud

  • Administrator
  • Hero Member
  • *****
  • Posts: 9026
Re: Vantage Firmware
« Reply #6 on: December 13, 2009, 06:47:39 AM »
 emu firmware vantage_hd+25501
With this Vantage Emu works S1-S8 and SCT

Testet by tom264

>Install, than in Menü 9999, Box Reboot, than works.
Logged
-----------------------------------------------








UNAUTHORIZED DECODING OF ENCRYPTED SIGNALS FROM EITHER DOMESTIC OR FOREIGN PROVIDERS IS AGAINST THE LAW !!!
INFORMATION CONTAINED IN MY POSTS ["C/P FROM ANOTHER SITE"] ARE FOR LEARNING AND EDUCATIONAL PURPOSES ONLY !!!
PLEASE, DO NOT SEND ME PRIVATE MESSAGES WITH TECHNICAL QUESTIONS, USE FORUM FOR IT !!!

Offline elcardinal74

  • Hero Member
  • *****
  • Posts: 2056
Re: Vantage Firmware
« Reply #7 on: December 26, 2009, 11:34:33 PM »
 Firmware X201S/X201SCI/X211S/X221S/X221SCI/X221TSCI Serie

Vantage 00.63.00.85AOA Mainware mit EMU !

Eclusivo!! TechSat Team
New Firmware per Vantage 200 Fix Sky

Cari amici in eclusiva sul nostro forum "per voi" potrete trovare il nuovo firmware per Vantage che fixa la lettura di Sky senza perdere la lettura anche all'abbonamento di SRG
Logged


Offline antox

  • Ferengi
  • Global Moderator
  • Hero Member
  • *****
  • Posts: 16798
Re: Vantage Firmware
« Reply #8 on: December 26, 2009, 11:54:27 PM »
New firmware modded for Vantage X200 series
New firmware modded for Vantage X200 series


Firmware Emu for Jepssen jst-2 modded to Vantage X200.

Ok Cardreader with SkYz card and added SCT Channels
Thanks to grantor & TechSatTeam
Logged

Offline mehdimaan

  • Newbie
  • *
  • Posts: 1
Re: Vantage Firmware
« Reply #9 on: June 14, 2010, 01:43:18 AM »
Hello to all.
I need last main and emu full shareware for Vantage X211S CI. Can you help me?
How can I use keys manually on receiver control ? Thanks alot for all.
Logged
Pages: [1]   Go Up
« previous next »