Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
News:
Home
Help
Login
Register
CardSharing-X
»
» Smartcards «
»
Card Discussion
»
Millenium card help?
« previous
next »
Print
Pages: [
1
]
Go Down
Author
Topic: Millenium card help? (Read 2162 times)
0 Members and 1 Guest are viewing this topic.
lakosta
Jr. Member
Posts: 73
Millenium card help?
«
on:
June 01, 2010, 06:18:33 PM »
How to program the millenium card with CAS 3 programmer?
Logged
lakosta
Jr. Member
Posts: 73
How to program MILLENIUM CARD?
«
Reply #1 on:
June 01, 2010, 06:20:06 PM »
How to program the millenium card with CAS 3 programmer?
Logged
antox
Ferengi
Global Moderator
Hero Member
Posts: 16798
Re: Millenium card help?
«
Reply #2 on:
June 01, 2010, 06:41:15 PM »
Cas3 and Millennium + Problem
Issues with Programming Millennium and Omnia+ Cards
Most problems with programming these cards are due to programmer’s bad configuration, Com ports, wrong cabling, usb to RS232 adapters, and pc conflicts.
Programmers
First of all make sure you have the correct programmer. Most programmers will work but you have to keep few things in mind:
The likes of Infinity phoenix, Cas 2 or 3, Dynamite, Smartbee, etc, which bring serial socket , will need both of them connected because data transmits trough physical serial connection and cable. On the cases of you having software that needs to be set for phoenix mode to work, as soon as you select that, the usb port only gets used to get programmer powered up. All transmissions are done trough serial. Those like that are the Infinity phoenix, Cas 2 or 3, Dynamite and similar. They do not have VCP-mode (Virtual com port)
Smartbee programmer is automatically set to phoenix as soon as you plug it but once again, you need physical serial port as only using the usb bit (only used to power up the programmer) will not work.
Only programmers like Infinity USB Unlimited, infinity smart, etc, with VCP-mode (Virtual com port) option are capable of creating a virtual port capable of transmitting data trough Usb.
Cables
Make sure you are using the right cables. The serial cable you use to connect must be 9-9pin, male-female wired straight thru
Adapters and convertors
Just because you have an adapter that installs, it does not mean it works. Make sure you buy a good and proved working one of them, so you are sure that port is actually created. PCMIA to RS232 are recommended for Lap tops instead of usb to serial ones. Also, make sure those are compatible with your operating system
Computer issues
Some firewall and security program installed on your pc, can block the functionality of you programnmers and loaders. Make sure your firewall or other, allow them to run.
Com ports
If you still have problems you could have a com port conflict. Uninstall the com port from System/device manager and install again to see if it works
Thanks to Joedenoble
How to program Millennium cards
First open the Millennium Card Loader v. 1.0.2 and set it as picture bellow. Select com port, tick Card Connector NO, also select fast or slow speed
Insert card and click Connect. Card will be recognized as Millennium or Millennium + depending on the version inserted
Click Program and direct program to where you have the millenium file stored. Highlight it and open
Card will start loading as picture bellow. When finished, disconnect and remove the card as it is programmed and ready for use
Thanks to Joedenoble for Tut.
Logged
lakosta
Jr. Member
Posts: 73
Re: Millenium card help?
«
Reply #3 on:
June 01, 2010, 09:20:26 PM »
Thank you very much for your help!
Logged
Print
Pages: [
1
]
Go Up
« previous
next »
CardSharing-X
»
» Smartcards «
»
Card Discussion
»
Millenium card help?