AZbox Enigma 2 by The_ripper - TEST

[antox]

azbox e2 v 1.0.26 by the ripper

Code Select Expand

Dear friends,

Enigma v1.0.26 by the_ripper and team


Attention:
Please, before installing Enigma 2 into Your device, read ReadMe file, which is attached with every releases.
Use at you own risk, this software in un-official and we cannot guarantee if there’s no possible damage on your hardware.

Code Select Expand

Enigma v1.0.26 by the_ripper and team

Sta je novo :

- Podrska za DiseQc ( 1.0, 1.1, 1.2 manuelno i putem USALS )

- DVB-S2 Podrska

- Integrisan skin cijenjenog nam kolege Mire , BlackShadow2

- Ispravljeni pojedini BUG-ovi .

Prije flashiranja potrebno instalirati novu verziju AzUP v1.1 programa. ( Dolazi zajedno sa Imageom u arhivi ).
E2_AZBox_1.0.26.rar

[antox]

Code Select Expand

Nakon sto instalirate E2, nemojte vaditi usb memory stick, ugasite resiver i upalite ga.

Resiver ce uci u RECOVERY MODE i ispisati ce Vam IP adresu.

Putem Putty-a telnetujte se na tu IP adresu i izvrsite sljedece komande :

username: root

password: azbox


mkdir /D

mount /dev/hda1 /D

Spojite se na resiver putem FTP-a i udjite u sljedeci direktorij :

/D/etc/init.d

tu prebacite bootup file koji se raspakirali iz bootup.zip filea.

Overwrite YES.

Uklonite USB , ugasite, pa zatim upalite vas resiver i sve je spremno za koriscenje.

Takodjer ova solucija vrijedi za sve koji su vec flashali resiver, dovoljno je samo da odu u RECOVERY MODE i da odrade gore navedene postupke.

Code Select Expand

After installing the E2, do not remove the USB memory stick, turn off receiver and turn it on.

The receiver will enter into recovery mode and print will take the IP address.

Via Putty and telnetujte on this IP address and perform the following command:

username: root

password: azbox


mkdir / D

mount / dev/hda1 / D

Connect to the receiver via FTP and enter the following directories:

/ D / etc / init.d

the switch bootup file that is unpacked from bootup.zip file.

Overwrite YES.

Remove the USB, shut down, then turn on your receiver and everything is ready for use.

Also, this solution is valid for all who have already flashali receiver, it is enough to go into recovery mode and that as doing the above actions.


[antox]

Enigma 2 v1.0.27

Devices suitable for flashing : Elite and Premium

What is new :

- DiseQc FIX ( 1.0 , 1.1 , 1.2 Manual and USALS too )

- DVB-S2 FIX

- Integrated BlackShadow2 skin by Matrix10

- Fixed boot error

Download:

Enigma v1.0.27
http://www.azbox-enigma.eu/upload/E2_AZBox_1.0.27.rar
ATTENTION: Use AzUP v1.1 for Flashing this version of Enigma 2 into Your devices !!!

[labud]

ATTENTION: Use AzUP v1.1 for Flashing this version of Enigma 2 into Your devices !!!

Code Select Expand

pls read readme.txt included in E2_AZBox_1.0.27.rar archive
_________________________________ __________________

How to use AZUp
Because they appeared quasi instructions for AZUp use and procedures for the insertion of E2 in AZBox
I prepared a short and precise instructions - exactly what you need to do
btw , I must to mention , ignore wrong "tutorials" with wrong directions
as : you must use Format App ))) realy funny because AZUp manage partitions of your AZBox
Ignore quasi instructions and use this official instruction from the author of AZUp


We have 3 situation :
I) You have Official FW in your AZBox andyou want to install E2
II) You have E2 in yourAZBox and now you want to install official FW
III) You have E2 in your AZBox and now you want to install new/update of E2


I) You have Official FW in your AZBox andyou want to install E2
Switch off AZBox
Put usb stick with patch.bin (e2)
switch on AZBox
Follow messages on GUI for update official FW (standard procedure)
After about 1 min , your receiver will reboot
Dont remove USB Stick from AZBox !!!
wait for IP adress on VFD of AZBox
Start latest ver of AZUp
Write IP adress in AZUp (see VFD)
Click on button Update
AZUp check for resque mode, also check ver of patch.bin (E2 or official fw)
AZUp create cramfs, Create 3 partition on DOM and formatted them
Copyng E2 kernel in Flash (about 2.5 min)
Copyng E2 files in first DOM partition (about 1 min)
when get popup msg - remove usb stick and wait for reboot (Rebooting... msg on VFD)
New E2 is installed successfully


II) You have E2 in yourAZBox and now you want to install official FW

Switch off AZBox
Put usb stick with patch.bin (Official FW)
switch on AZBox
wait for IP adress on VFD of AZBox
Start latest ver of AZUp
Write IP adress in AZUp (see VFD)
Click on button Update
AZUp check for resque mode, also check ver of patch.bin (E2 or official fw)
AZUp Create 4 partition on DOM and formatted them
Copyng Official (old) kernel in Flash (about 2.5 min)
when get popup msg - first part of update is done, but dont remove USB stick from AZBOX
wait for reboot , and follow messages on GUI for update official FW (standard procedure)



III) You have E2 in your AZBox and now you want to install new/update of E2

Switch off AZBox
Put usb stick with patch.bin (e2)
switch on AZBox
wait for IP adress on VFD of AZBox
Start latest ver of AZUp
Write IP adress in AZUp (see VFD)
Click on button Update
AZUp check for resque mode, also check ver of patch.bin (E2 or official fw)
AZUp create cramfs, Create 3 partition on DOM and formatted them
Copyng E2 kernel in Flash (about 2.5 min)
Copyng E2 files in first DOM partition (about 1 min)
when get popup msg - remove usb stick and wait for reboot (Rebooting... msg on VFD)
New E2 is installed successfully

[antox]

Enigma 2 v1.0.28

Devices suitable for flashing : Elite and Premium

What is new :

- Fix for no signal on DVB-S2 tuner for some users

- Multimedia fix for various formats by sattomy

Download:

E2_AZBox_1.0.28
http://azbox-enigma.eu/upload/E2_AZBox_1.0.28.rar
ATTENTION: Use AzUP v1.1 for Flashing this version of Enigma 2 into Your devices !!!

[antox]

CCcam & Mgcam (E2) for AzBox HD

Pack contenente :

- ipk per script manager
- ipk con Mgcam1.35a
- ipk con CCcam2.1.4

scompattare sul PC, trasferire i file in /tmp
installare per prima "enigma2-plugin-extensions-userscripts_2.4-r4_mipsel.ipk"
a seguire quelli delle cam o della cam che vi interessa.
riavviare il decoder
tasto blu -> user script

[antox]

Enigma 2 v1.0.29

Devices suitable for flashing : Elite and Premium

What is new :

- MyTube plugin (YouTube)

- Multimedia fix for various formats by sattomy
ATTENTION: Use AzUP v1.1 for Flashing this version of Enigma 2 into Your devices !!!



http://www.azbox-enigma.eu/

[antox]

Enigma 2 v1.0.30

Devices suitable for flashing : Elite - Premium - Premium+

What is new :

- P+ tuner driver tested

- P+ FAN control enabled and activated

- some fixes in audio - volume control now is ok, mute/unmute also

- plus few more fixes

NAPOMENA: Prilikom ubacivanja FW nakon vadjenja sticka dodje do 25 i izbaci model ovisno koji imate i tu zastane, zato NE UBACUJTE dok fix ne izadje


http://www.azbox-enigma.eu/e107/news.php?item.4.2

[labud]

AZUP 1.2a (Go Back Fix)

FIX for returning to original Firmware

[labud]

AZUP 1.2a (Go Back Fix)

FIX for returning to original Firmware