CardSharing-X
» Receivers « => DreamBox Emulators => » DREAMBOX ZONE « => Mbox => Topic started by: bordan on August 31, 2009, 11:58:57 AM
-
mbox 0.4 BETA build 0023 sa podrskom za (gbox)
ova je jedna od naj stabilnih verzija mboxa a mozete je koristiti i za gbox protokol posto boje radi sa nds cartama od (bilo koje verzije gboxa)
sve je spremno samo ubaci cwshare.cfg i you are on line
-
kako napraviti da rade d+ kanali sa ovim ili sa ovom verzijom ne radi taj paket uopce ?
-
jel moguce da nitko ne zna odgovor ?
-
prijatelju zaÅ¡to si se baÅ¡ odlučija za mbox..on je proÅ¡lo svrÅ¡eno vrime..nema niÅ¡ta viÅ¡e od njega..pozz bgd_82cc9c0b21e2c7fb3ade9961fc
-
samo da mi prorade Spanjolci ( D+ ) meni ne treba nista bolje , iznenadio sam se kako se mbox nosi sa gbox serverima ,jer ja zapravo imam gbox D linije i takvu i razmjenjujem ali kad te linije koristim sa mbox-om rade odlicno NDS otvara za 1-2 sekunde ,rijetko koji kanal da zapne da mu treba duze da ga otvori a kad otvori stabilno radi jeko malo trzaja gotovo zanemarivo, u sat vremena ako trzne 3-4 puta na sekundu-dvije ,to je nista.
-
potrudit čemo se nač rjeÅ¡enje da prorade Å panjolci..nema druge prijo načemo ...
-
kako napraviti da rade d+ kanali sa ovim ili sa ovom verzijom ne radi taj paket uopce ?
daj postavi ovdje postavke iz cw share - X:,N:,I: i O: liniju
te kompletan mbox.cfg
proradit ce d+ a025
-
I: { 02 }
N: { 00 01 13 00 9000 12000 }
X: { 08 }
O: liniju nemam u cwshare fileu koji sam koristio za gbox
Sto se tice mbox.cfg on izgleda ovako :
//mbox.cfg EXPLANATION and EXAMPLES
A: { 0 } // for QBoxHD receivers or for any receivers if needed it
//A: { x }
//Choose adapter path
//x=0 -> /dev/dvb/adapter0/
//x=1 -> /dev/dvb/adapter1/
//x=2 -> /dev/dvb/adapter2/
//x=.. -> .......
//default x=0
D: { 0 }
//D: { x }
//x=0 -> disable
//x=1 -> enable dbox2 cw writing
//x=2 -> enable STAPI for IPBOX
//x=3 -> enable STAPI for Kathrein
//x=4 -> enable Linux DVB API for Kathrein
//x=5 -> enable triple dragon
//x=6 -> enable Qbox HD
//default disabled
B: { 1 }
//B: { x }
//x=0 -> disable local UDP ports 8004-80xx ,this ports are used with DVB cards and gbox plugin (Windows and Linux)
//x=1 -> enable
//default disabled
Z: { 12 } { 127.0.0.1 8000 }
// Z option -> control sending/writing current informations
// Z: { xy } { IP port }
// x=0 -> don't print time stamp (in console screen and in debug file)
// x=1 -> print time stamp ( .... )
// y=0 -> no writing/sending informations to debug file/destination IP
// y=1 -> send informations to destination IP but not in debug file
// y=2 -> write informations to debug file but don't send to destination IP
// y=3 -> write/send informations to debug file/destination IP
// IP port -> destination IP and UDP port where to send informations
// no default
#C: { 127.0.0.1 7999 }
// C option -> control receiving some command messages localy or from another IP
// C: { IP port }
// IP-> your local IP or you DNS
// port -> on what port you will be waiting command messages
// no default
U: { 1 }
// U options -> Update peer(s) IP if it changes while peer still resending ecm's/cw etc.. information
// default only on hello message peer(s) IP are updated !!!
// U: { x }
// x=0 -> disabled
// x=1 -> enabled
// default disabled
L: { 1 }
// L option -> how mbox to menage virtual card(s) with level 0
// ( only for peer(s) who have and can reshare virtual cards but don't want to use LEVEL 0 card(s) for them self)
// L: { x }
// x=0 -> don't load any virtual cards with LEVEL 0, you can't use them for your self
// x=1 -> load all virtual cards with LEVEL 0 ,you will be using them for your self
// default 1
#G: { /hdd/ }
//G option -> redirect writing ONLY debug.txt file to internal or external HDD in receivers or for any other reason.
//Remove #, ONLY if you want to use this option !!!!!!!
T: { ./ }
// T option -> where to store temp files ... (share.info,debug.txt ,etc.)
// T: { folder_path_to_files, example: T: { /tmp/ } }
K: { ./ }
// K option -> where is cwshare.cfg,mbox.prio file
// K: { folder_path_to_files, example: K: { /var/keys/ } }
M: { 1 }
// M option -> Mode option
// M: { x }
// x=0 -> local mode no NET
// x=1 -> NET mode
// default 0
P: { 1/tmp/camd.socket }
// P option -> PMT location (Dont used with linux and windows)
// you must be tuned to channel so image can generate this file
// { /tmp/pmt.tmp } for receivers and images that create this file <- use this if you can
// { /tmp/pmtX.tmp } X-> number -> pmt1.tmp ......
// { 1/tmp/camd.socket } for enigma 1
// { 2/tmp/camd.socket } for enigma 2
W: { 0 }
// W option -> write raw ECM to ecm.raw file
// W: { x }
// x=0 -> disabled
// x=1 -> enabled
// default disabled
Q: { 300 }
//Q option -> newcamd connect retry in sec.
//Q: { x }
// default 300 sec.
F: { 500 }
//F option -> reset writing debug.txt from begining if file size is higher then (x)(KB)
//F { x } -> decimal in KBytes
//default 500 KB
///DO NOT USE THIS ,NOT TESTED !!!!!!!!//
//V: { card_type device clock inverse_Reset}
#V: { 3 1 3571200 0 }
#V: { 3 2 3571200 1 }
// card_type:
// Seca 3 , 1rd3t0 4, Conax 5, Cryptoworks 6, Viaccess 7, NDS 8, Nagravision 9
// device:
// COM1/ttyS0 1
// COM2/ttyS1 2
// /dev/sci0 3
// /dev/sci1 4
// /dev/usb/tts/0 5
// /dev/usb/tts/1 6
// /dev/tts/0 7
// /dev/tts/1 8
// /dev/ttyUSB0 9
// /dev/ttyUSB1 10
//clocks for COM ports in Hz
//for SCI slots use this values
// 1 - 3.33 Mhz
// 2 - 3.63 Mhz
// 3 - 4 Mhz
// 4 - 4.44 Mhz
// 5 - 5Mhz
// 6 - 5.71 Mhz
// 7 - 6.66 Mhz
// 8 - 8 Mhz
//Inverse Reset
// 1 -yes
// 0 -no
///DO NOT USE THIS ,NOT TESTED !!!!!!!!//
J: { 1 }
// J option -> enable adding betacrypt header to N3 ECM for Premier
// J { x }
// x = 0 -> disabled
// x = 1 -> enabled
R: { 3600 }
// only for gboxx, dont work on mbox protocol
// R option -> resend hello to all peers after X seconds, ony for gboxx peers,not mbox peers
//default in code 3600 seconds
H: { a b c d e f }
// only for gboxx, dont work on mbox protocol
// H option -> mapping provid (0-disabled, 1-enabled)
//H: { a b c d e f }
//a-> mapping all 0BXX to 0B00
//b-> mapping 1810 to 1801
//c-> mapping 1803 to 1801
//d-> mapping 1802 to 1801
//e-> mapping 1815 to 1801
//f-> mapping 1822 to 1801
S: { COM1 }
//S option -> enable sssp protocol
//S: { x}
//x=COM1
//x=COM2
//x=/dev/ttyS0
//x=/dev/ttyS1
-
Pozdrav Gogivk Radi D+ na mbox 4.23 odlicno netreba neke posebne postavke samo validna karta izgleda imas mnogo ,,fake" karata moras naci validnu kartu .
Probaj prvo svaki peer posebno iskjuci ostale videces ko ima ispravnu kartu ako to ne uspes ovako.
P: { xxxxyyyy boxid;boxid;boxid;....; }
P: { xxxxyyyy boxid;boxid;boxid;....; }
P: { xxxxyyyy boxid;boxid;boxid;....; }
example:
P: { 0100006A A1A2;B1B2;C1C2;...; }
Kod tebe
P: { 01004106 A1A2;ovde;ovdebox;...; }
mbox will only send ECM to this (A1A2;B1B2;C1C2) boxids for 0100006A.All other networks cards will be ignored!!!!!.
Ako i ovo ne uspe trazi peera sa validnom karu za D+ RADI 100% bez neke posebne postavke ali sa validnom kartom.
-------------
-
Hvala pogledat cu i probati ovo sto mi kazes , ali imam bar 7-8 ispravnih karti koje mi rade na gboxu i vidim da one dolaze i uvdje uredno samo sto rekoh gbox mi dosta trza u odnosu na ovu verziju mboxa. probat cu pa cu javiti kasnije jesam sto uspjeo.
-
Probao sam staviti ovako P linije i to sam stavio one karte koje znam da rade na gboxu i opet nista od D+, a linije za pink koje sam probao na ovaj nacin uredno povuce bas od tih koje sam dao kao prioritetne
-
sad postavi ovako:
u cwshare.cfg
I: { 2 }
N: { 400 200 }
X: { 8 }
O:{ 2000 1000 }
u mbox.cfg
//mbox.cfg EXPLANATION and EXAMPLES
#A: { 0 } // for QBoxHD receivers or for any receivers if needed it
//A: { x }
//Choose adapter path
//x=0 -> /dev/dvb/adapter0/
//x=1 -> /dev/dvb/adapter1/
//x=2 -> /dev/dvb/adapter2/
//x=.. -> .......
//default x=0
#D: { 0 }
//D: { x }
//x=0 -> disable
//x=1 -> enable dbox2 cw writing
//x=2 -> enable STAPI for IPBOX
//x=3 -> enable STAPI for Kathrein
//x=4 -> enable Linux DVB API for Kathrein
//x=5 -> enable triple dragon
//x=6 -> enable Qbox HD
//default disabled
#B: { 1 }
//B: { x }
//x=0 -> disable local UDP ports 8004-80xx ,this ports are used with DVB cards and gbox plugin (Windows and Linux)
//x=1 -> enable
//default disabled
Z: { 12 } { 127.0.0.1 8000 }
// Z option -> control sending/writing current informations
// Z: { xy } { IP port }
// x=0 -> don't print time stamp (in console screen and in debug file)
// x=1 -> print time stamp ( .... )
// y=0 -> no writing/sending informations to debug file/destination IP
// y=1 -> send informations to destination IP but not in debug file
// y=2 -> write informations to debug file but don't send to destination IP
// y=3 -> write/send informations to debug file/destination IP
// IP port -> destination IP and UDP port where to send informations
// no default
#C: { 127.0.0.1 7999 }
// C option -> control receiving some command messages localy or from another IP
// C: { IP port }
// IP-> your local IP or you DNS
// port -> on what port you will be waiting command messages
// no default
U: { 1 }
// U options -> Update peer(s) IP if it changes while peer still resending ecm's/cw etc.. information
// default only on hello message peer(s) IP are updated !!!
// U: { x }
// x=0 -> disabled
// x=1 -> enabled
// default disabled
L: { 1 }
// L option -> how mbox to menage virtual card(s) with level 0
// ( only for peer(s) who have and can reshare virtual cards but don't want to use LEVEL 0 card(s) for them self)
// L: { x }
// x=0 -> don't load any virtual cards with LEVEL 0, you can't use them for your self
// x=1 -> load all virtual cards with LEVEL 0 ,you will be using them for your self
// default 1
#G: { /hdd/ }
//G option -> redirect writing ONLY debug.txt file to internal or external HDD in receivers or for any other reason.
//Remove #, ONLY if you want to use this option !!!!!!!
T: { /tmp }
// T option -> where to store temp files ... (share.info,debug.txt ,etc.)
// T: { folder_path_to_files, example: T: { /tmp/ } }
K: { var/keys }
// K option -> where is cwshare.cfg,mbox.prio file
// K: { folder_path_to_files, example: K: { /var/keys/ } }
M: { 1 }
// M option -> Mode option
// M: { x }
// x=0 -> local mode no NET
// x=1 -> NET mode
// default 0
P: { /tmp/pmt.tmp }
// P option -> PMT location (Dont used with linux and windows)
// you must be tuned to channel so image can generate this file
// { /tmp/pmt.tmp } for receivers and images that create this file <- use this if you can
// { /tmp/pmtX.tmp } X-> number -> pmt1.tmp ......
// { 1/tmp/camd.socket } for enigma 1
// { 2/tmp/camd.socket } for enigma 2
W: { 0 }
// W option -> write raw ECM to ecm.raw file
// W: { x }
// x=0 -> disabled
// x=1 -> enabled
// default disabled
Q: { 3 }
//Q option -> newcamd connect retry in sec.
//Q: { x }
// default 300 sec.
F: { 300 }
//F option -> reset writing debug.txt from begining if file size is higher then (x)(KB)
//F { x } -> decimal in KBytes
//default 500 KB
///DO NOT USE THIS ,NOT TESTED !!!!!!!!//
//V: { card_type device clock inverse_Reset}
#V: { 3 1 3571200 0 }
#V: { 3 2 3571200 1 }
// card_type:
// Seca 3 , 1rd3t0 4, Conax 5, Cryptoworks 6, Viaccess 7, NDS 8, Nagravision 9
// device:
// COM1/ttyS0 1
// COM2/ttyS1 2
// /dev/sci0 3
// /dev/sci1 4
// /dev/usb/tts/0 5
// /dev/usb/tts/1 6
// /dev/tts/0 7
// /dev/tts/1 8
// /dev/ttyUSB0 9
// /dev/ttyUSB1 10
//clocks for COM ports in Hz
//for SCI slots use this values
// 1 - 3.33 Mhz
// 2 - 3.63 Mhz
// 3 - 4 Mhz
// 4 - 4.44 Mhz
// 5 - 5Mhz
// 6 - 5.71 Mhz
// 7 - 6.66 Mhz
// 8 - 8 Mhz
//Inverse Reset
// 1 -yes
// 0 -no
///DO NOT USE THIS ,NOT TESTED !!!!!!!!//
#J: { 1 }
// J option -> enable adding betacrypt header to N3 ECM for Premier
// J { x }
// x = 0 -> disabled
// x = 1 -> enabled
#R: { 3600 }
// only for gboxx, dont work on mbox protocol
// R option -> resend hello to all peers after X seconds, ony for gboxx peers,not mbox peers
//default in code 3600 seconds
#H: { a b c d e f }
// only for gboxx, dont work on mbox protocol
// H option -> mapping provid (0-disabled, 1-enabled)
//H: { a b c d e f }
//a-> mapping all 0BXX to 0B00
//b-> mapping 1810 to 1801
//c-> mapping 1803 to 1801
//d-> mapping 1802 to 1801
//e-> mapping 1815 to 1801
//f-> mapping 1822 to 1801
#S: { COM1 }
//S option -> enable sssp protocol
//S: { x}
//x=COM1
//x=COM2
//x=/dev/ttyS0
//x=/dev/ttyS1
probaj pa javi rezultat
-
Probao ,odmah me izbacio ,cim sam pokrenuo stao je i izbacio ovu zadnju poruku ,prije ove promjene se spoji uredno na sssp protokol
[18:47:18] ===> Net Mode <===
[18:47:18] Creating sssp worker thread for COM1...OK
[18:47:18] Failed to open cwshare.cfg file !!!!
[18:47:18] Exiting ...
drugi put ovo kad sam sve prekopirao sto si napisao pokazao je ovo
[18:52:00] ===> Net Mode <===
[18:52:00] Failed to open cwshare.cfg file !!!!
[18:52:00] Exiting ...
-
ok
vrati stari mbox.cfg file kako si gore napisao
ali Q: { 300 } stavi na 3
nisi gore napisao jel pc ili dreambox u pitanju,pa sam podesio cfg za dreambox
-
Da to nisam napomenuo ovdje, pokrecem mbox na PC , probao sam i ovo zadnje sto si rekao i ista stvar nista jos. baš cudno i digi tv radi neki su imali s njim problem oko pokretanja ali evo kod mene d+ zeza.
hvala na trudu sto zelis pomoci ako jos imas neku ideju i vremena naravno reci ako ne ,jos jednom hvala.
-
//mbox.cfg EXPLANATION and EXAMPLES
evo moj konfig 100 % radi D+ . Mbox 4.23 - PC Windows
--------------------------------------------------------------------------------
A: { 0 } // for QBoxHD receivers or for any receivers if needed it
//A: { x }
//Choose adapter path
//x=0 -> /dev/dvb/adapter0/
//x=1 -> /dev/dvb/adapter1/
//x=2 -> /dev/dvb/adapter2/
//x=.. -> .......
//default x=0
D: { 0 }
//D: { x }
//x=0 -> disable
//x=1 -> enable dbox2 cw writing
//x=2 -> enable STAPI for IPBOX
//x=3 -> enable STAPI for Kathrein
//x=4 -> enable Linux DVB API for Kathrein
//x=5 -> enable triple dragon
//x=6 -> enable Qbox HD
//default disabled
B: { 1 }
//B: { x }
//x=0 -> disable local UDP ports 8004-80xx ,this ports are used with DVB cards and gbox plugin (Windows and Linux)
//x=1 -> enable
//default disabled
Z: { 12 } { 127.0.0.1 8000 }
// Z option -> control sending/writing current informations
// Z: { xy } { IP port }
// x=0 -> don't print time stamp (in console screen and in debug file)
// x=1 -> print time stamp ( .... )
// y=0 -> no writing/sending informations to debug file/destination IP
// y=1 -> send informations to destination IP but not in debug file
// y=2 -> write informations to debug file but don't send to destination IP
// y=3 -> write/send informations to debug file/destination IP
// IP port -> destination IP and UDP port where to send informations
// no default
#C: { 127.0.0.1 7999 }
// C option -> control receiving some command messages localy or from another IP
// C: { IP port }
// IP-> your local IP or you DNS
// port -> on what port you will be waiting command messages
// no default
U: { 1 }
// U options -> Update peer(s) IP if it changes while peer still resending ecm's/cw etc.. information
// default only on hello message peer(s) IP are updated !!!
// U: { x }
// x=0 -> disabled
// x=1 -> enabled
// default disabled
L: { 1 }
// L option -> how mbox to menage virtual card(s) with level 0
// ( only for peer(s) who have and can reshare virtual cards but don't want to use LEVEL 0 card(s) for them self)
// L: { x }
// x=0 -> don't load any virtual cards with LEVEL 0, you can't use them for your self
// x=1 -> load all virtual cards with LEVEL 0 ,you will be using them for your self
// default 1
#G: { /hdd/ }
//G option -> redirect writing ONLY debug.txt file to internal or external HDD in receivers or for any other reason.
//Remove #, ONLY if you want to use this option !!!!!!!
T: { ./ }
// T option -> where to store temp files ... (share.info,debug.txt ,etc.)
// T: { folder_path_to_files, example: T: { /tmp/ } }
K: { ./ }
// K option -> where is cwshare.cfg,mbox.prio file
// K: { folder_path_to_files, example: K: { /var/keys/ } }
M: { 1 }
// M option -> Mode option
// M: { x }
// x=0 -> local mode no NET
// x=1 -> NET mode
// default 0
P: { /tmp/pmt.tmp }
// P option -> PMT location (Dont used with linux and windows)
// you must be tuned to channel so image can generate this file
// { /tmp/pmt.tmp } for receivers and images that create this file <- use this if you can
// { /tmp/pmtX.tmp } X-> number -> pmt1.tmp ......
// { 1/tmp/camd.socket } for enigma 1
// { 2/tmp/camd.socket } for enigma 2
W: { 0 }
// W option -> write raw ECM to ecm.raw file
// W: { x }
// x=0 -> disabled
// x=1 -> enabled
// default disabled
Q: { 300 }
//Q option -> newcamd connect retry in sec.
//Q: { x }
// default 300 sec.
F: { 500 }
//F option -> reset writing debug.txt from begining if file size is higher then (x)(KB)
//F { x } -> decimal in KBytes
//default 500 KB
///DO NOT USE THIS ,NOT TESTED !!!!!!!!//
//V: { card_type device clock inverse_Reset}
#V: { 3 1 3571200 0 }
#V: { 3 2 3571200 1 }
// card_type:
// Seca 3 , 1rd3t0 4, Conax 5, Cryptoworks 6, Viaccess 7, NDS 8, Nagravision 9
// device:
// COM1/ttyS0 1
// COM2/ttyS1 2
// /dev/sci0 3
// /dev/sci1 4
// /dev/usb/tts/0 5
// /dev/usb/tts/1 6
// /dev/tts/0 7
// /dev/tts/1 8
// /dev/ttyUSB0 9
// /dev/ttyUSB1 10
//clocks for COM ports in Hz
//for SCI slots use this values
// 1 - 3.33 Mhz
// 2 - 3.63 Mhz
// 3 - 4 Mhz
// 4 - 4.44 Mhz
// 5 - 5Mhz
// 6 - 5.71 Mhz
// 7 - 6.66 Mhz
// 8 - 8 Mhz
//Inverse Reset
// 1 -yes
// 0 -no
///DO NOT USE THIS ,NOT TESTED !!!!!!!!//
J: { 1 }
// J option -> enable adding betacrypt header to N3 ECM for Premier
// J { x }
// x = 0 -> disabled
// x = 1 -> enabled
R: { 3600 }
// only for gboxx, dont work on mbox protocol
// R option -> resend hello to all peers after X seconds, ony for gboxx peers,not mbox peers
//default in code 3600 seconds
H: { 0 0 0 0 0 0 }
// only for gboxx, dont work on mbox protocol
// H option -> mapping provid (0-disabled, 1-enabled)
//H: { a b c d e f }
//a-> mapping all 0BXX to 0B00
//b-> mapping 1810 to 1801
//c-> mapping 1803 to 1801
//d-> mapping 1802 to 1801
//e-> mapping 1815 to 1801
//f-> mapping 1822 to 1801
S: { COM2 }
//S option -> enable sssp protocol
//S: { x}
//x=COM1
//x=COM2
//x=/dev/ttyS0
//x=/dev/ttyS1
-
eksperimentiraj sa X: opcijom
probaj X=5 pa navise do X=10
ako nece,onda je liku kartica istekla - ima je u boxu ali ne otvara nista
-
ovo je u moj cwshare.+ verziju sto sam postavio na forum = 100% radi D+ bez problema sa ispravnom kartom
I: { 02 }
X: { 10 }
N: { 00 01 03 3F 4000 6000 }
sada sa ovim postavkama gledam D+
-----------------------------------------------------
znaci samo eksperimentiraj sa kartama dok ne nadzes neku sto radi
-
ovo je u moj cwshare.+ verziju sto sam postavio na forum = 100% radi D+ bez problema sa ispravnom kartom
I: { 02 }
X: { 10 }
N: { 00 01 03 3F 4000 6000 }
sada sa ovim postavkama gledam D+
-----------------------------------------------------
znaci samo eksperimentiraj sa kartama dok ne nadzes neku sto radi
imas krivu N: liniju i povremeni trzaji ti mogu doci bas od nje
ta N: linija se koristi samo za gbox,za mbox nikako
za mbox linija ide ovako N: { 400 200 } i nikako drugacije a025
-
Ok hvala kolega ali nemam nikakvih trzaja sve radi prelepo .
-
i meni je dobro radio sa tom N linijom od gboxa ,a sad sam stavio ovu evo vec 20 minuta ni jedan trzaj nije napravio , izgleda da jos bolje radi ,eh da nije toga D+ cista petica bi bila
-
i meni je dobro radio sa tom N linijom od gboxa ,a sad sam stavio ovu evo vec 20 minuta ni jedan trzaj nije napravio , izgleda da jos bolje radi ,eh da nije toga D+ cista petica bi bila
naravno da bolje radi,kad je sam autor mboxa to napomenuo
N: { 00 01 03 3F 4000 6000 } - neispravno
N: { 4000 2000 } - ispravno
kaj se tice D+ potrazi drugog peera,pa ces vidjeti da radi a025
-
N: { 4000 2000 }
N: { 400 200 }
Sad si mi naveo dva primjera , jel ovaj donji tocan ? Probao sam oba i nisam vidio neku razliku, ostavio sam N: { 400 200 }
-
N: { 4000 2000 }
N: { 400 200 }
Sad si mi naveo dva primjera , jel ovaj donji tocan ? Probao sam oba i nisam vidio neku razliku, ostavio sam N: { 400 200 }
izvini,moja greska
ovo je ispravna N: linija
N: { 400 200 }
-
Doticna n linija ima smisla samo za nds sistem i to ,,fino podesavanje" ako imas los odziv same karte nece ti to puno pomoci.
NDS system ->Resending ECM(s) on timeout interval
=================================================
N: { xxxx yyyy }
---------------------------------------------------------------
Evo ovde ---------(default disabled)--------------...
--------------------------------------------------------------
Ja bi te posovetovao ipak drugo tvoj problem za D+ nece resiti nikakva N linija (Mislim da je to bio tvoje glavno pitanje)ako vec radi na obicnom gboxa a ne radi na mbox isprobaj HDVB koji ima sopstven gbox + ,moznos da radi kao plugin
http://cardsharing-x.com/index.php/topic,5814.0.html (http://cardsharing-x.com/index.php/topic,5814.0.html)
-
jel ima di objasnjeno kako se ovo pokrece, one datoteke sam prekopirao u windowsw system32 folder i program se ptvori ali ne iscitava karte uopce.
-
jel ima di objasnjeno kako se ovo pokrece, one datoteke sam prekopirao u windowsw system32 folder i program se ptvori ali ne iscitava karte uopce.
Koristis ga na isti nacin kao mbox zasto si kopirao datoteke u windows system32 folder ?
raspakujes ga u jedan folder ubacis cwshare pa HDVB.exe (Active gbox cekiras i to je to ) a dodatak da radi kao plugin kopiras u programu koji koristis -isti nacin kao mbox.
-
Taj program nece ni da radi dok se te prilozene dll datoteke ne kopiraju u windows, a za mbox uopce ne koristim plugin jel nije potreban samo pokrenem mbox control koji sam pokrene mbox i uspostavi vezu sa risiverom preko sssp rs232 kabla.
-
Taj program nece ni da radi dok se te prilozene dll datoteke ne kopiraju u windows, a za mbox uopce ne koristim plugin jel nije potreban samo pokrenem mbox control koji sam pokrene mbox i uspostavi vezu sa risiverom preko sssp rs232 kabla.
(Neznam koji servise pak xp koristis ja ih nisam instalirao) isto ovaj program ima sssp podrsku a plugin koristis ako imas
primer sky star ako nemas nije ti potreban bas isto kako kod mboxa.
(http://img24.imageshack.us/img24/2825/hdvb.png) (http://img24.imageshack.us/i/hdvb.png/)
-
Rijesio sam ovaj problem ali samo djelomicno otvara mi d+ ali samo sa nagrom 1801 ReShareN3 2.25d/nagravision CAid, a sa 01004106 Digital+(19E)[tunneled SecaNagra] nece, jel to normalno za mbox 0.4 023 ili je to inace problem mboxu sto ne vjerujem, a ovih kartica mi dolazi puno i to dosta ispravnih koje mi rade na gboxu inace. jel zna netko o cemu se radi ?