CardSharing-X
» SAT Related « => Satellite Equipment => Topic started by: labud on October 29, 2009, 02:42:46 PM
-
Kako spojiti 16LNB-a na T90
(http://img222.imageshack.us/img222/5499/sur420f16satelitavarija.jpg)
EMP Centauri 17/1
(http://www.emp-centauri.cz/images/products/s_16_1_pcp_w3.jpg)
(http://www.emp-centauri.cz/images/util/S16_1PCPW3-rec.gif)
Linkovi
http://www.emp-centauri.cz/products.php?id_kateg=5&id_pkateg=45&id=284 (http://www.emp-centauri.cz/products.php?id_kateg=5&id_pkateg=45&id=284)
User manual:
http://www.emp-centauri.cz/pdf/Profi_line_S16-1.pdf (http://www.emp-centauri.cz/pdf/Profi_line_S16-1.pdf)
Instruction manual
Connection
* Product S 16/1 PCP-W3 is a multi-mode satellite DiSEqC switch, designed for connecting of up to 16 satellite converters (LNBs) and terrestrial antenna to 1 user.
* Before installation, remove the product from plastic shield and connect coaxial cables from each LNB into satellite input ports (“SAT1 IN†to “SAT16 INâ€).
* It is recommended to write down assignment of inputs for receiver's setup and future reference.
* If required, connect cable from terrestrial antenna into port “TERR IN†and use appropriate wall socket or frequency splitter to separate satellite and terrestrial bands on user end of coaxial cable.
* Note: there is no DC feed provided on terrestrial input.
Modes of operation
Set desired operation mode by means of DIP switch - located on rear side of metal housing.
There are four modes of operation available:
1. DiSEqC 1.0 (committed switch - position/option A to D, available inputs 1 to 4)
2. DiSEqC 1.1 (uncommitted switch 1 to 16)
3. Combined DiSEqC 1.0 & 1.1 (committed switch - position/option A to D, uncommitted switch 1 to 4)
4. DiSEqC 1.2 (16 motor positions)
Mode selection guide
* Use DiSEqC 1.1 mode, if your receiver supports uncommitted switch parameter 1 to 16.
* Use DiSEqC 1.0 & 1.1 mode, if your receiver supports uncommitted switch parameter 1 to 4 only.
* In this case set committed switch as well. If the receiver doesn't support DiSEqC 1.1 mode at all, use DiSEqC 1.2 mode and carry out configuration procedure for motorized antenna.
* See product sticker located on plastic shield for detailed information on DIP switch levers positions (ON position is set when the lever is pressed down) and required DiSEqC parameters.
* Note: mode setting change (DIP switch levers positions) will take affect only after reset is performed.
---------------------------------------------------------
Po podacima to je izvanredno rješenje!
* Radi u 4 moda koja se prebacuju preklopkom.
* Podržava DiseqC 1.1 mod rada sa 16 ili 4 uncommitted switcheva.
* Kad radi sa 4 uncommitted switch (mod 3) -> podešava se kao i SPAUN SUR420F u Mode1, ali joj nisu potrebne još 4xDiseqC 4/1 sklopke!
* Kad sklopka radi u mod 2 teoretski se na nju može spojiti 64 LNB-a, jasno na svaki uncommitted port bi tada trebala ići po jedna DiseqC 4/1 sklopka.
* Jasno, tu treba tesitrati brzinu rada i možebitne probleme sa prebacivanjem ulaza...
Već se pojavila u prodaji ali u susjednoj Italiji:
Cijena je 62EUR -> 450kn
Ako se uzme u obzir da nisu potrebne dodatne sklopke za 16 satelita -> to je OK cijena...
Link:
http://www.mondotec.it/product.asp?ProdID=13671 (http://www.mondotec.it/product.asp?ProdID=13671)
Velika hvala kolegi njezicu za slike i iscrpne informacije i kolegi macro za sve skupa sastavljanju u jednu cjelinu hvala im obojici