Menu:
Manual Scan- From this menu you can perform other types of searches, from the full satellite to a single transponder to look Feeds
Menu:
SatFinder
- SatFinder is the search engine, you can check the quality of the signal, as shown in the picture you can change various settings to be more specific and check some transponder, this will allow you to further adjust the antenna.
Menu:
Positioner Setup- If you are using motor is not my case, this menu will allow you to move the engine back and forth to adjust the signal, you can also record every position of each satellite with a number, you'll need this if your antenna does not use USALS mode, or if your antenna is moved over the years.
When I did the manual had no motor, I can not display this image.
We left the Service Searching menu and the following:
SystemMenu:
A/V SettingsVideo Output: is the output of video we are using, if you must configure DVI HDMI
- In the latest version of BH that have changed and now offers HDMI
Mode: Here you set the screen size if you use a 1080i HD TV is your configuration, you have several options
- 480i - 60Hz
- 480p - 60Hz
- 576i - 50Hz
- 576p - 50Hz
- 720p - 50Hz
- 1080i - Multi -> 50Hz -> 60Hz
Refresh Rate: the configuration of the refresh, if you leave it in Multi 1080i
4:3 Content Display As: [/ B] If we have a 4:3 TV you can set the video window in different ways, if you have a 16:9 tv and I like to watch 4:3 content full screen need to select Just Scale
- Pillarbox
- Just Scale
- No Lineal
- Pan&Scan
Display 16:9 Content As: If we have a 4:3 tv can set the video window in different ways
- Letterbox
- Just Scale
- Pan&Scan
Dolby Digital Default: forcing you to use the Dolby Digital Audio, if you have connected an audio amplifier can enable this option.
Dolby Digital Downmix: normally activate it unless you use external audio amplifier
General Dolby Digital Delay: can delay the audio to fit the video if you have any problems
General PCM Delay: can delay the audio to fit the video if you have any problems
OSD Visibility: transparency of the menus in general
Scaler Sharpness: sharpness of the scaling
Menu:
Autoresolution- You can configure each of the video signals, aligns the signal we send to our TV
Menu:
LanguageMenu:
Customize
As we see in the picture, is in Setup Mode Intermediate, Expert to change it to have all the options available.
Setup Mode:
Recordings Always Have Priority: If you only have one tuner or an antenna, and use scheduled recording, this feature must be activated, forcing the tuner to use the recording as a priority channel, if you're in another channel does not use the same polarity would have problems.
Before Record Margin (minutes): Some channels do not meet the schedule, sometimes to speed up or slow it as much as usual, when you schedule a recording, it's annoying you're missing 2 or 3 minutes first, or left you, from this option you can adjust the start of recording in general.
After Margin Record: Same as above, but to adjust to the recording, you can give a few minutes more to you do not miss the end of your favorite event
Show Blinking Clock In Display Düring Recording: According to the model VU + with this option is more or less useful, indicates that it has started a recording, may be from the flickering of the hour, to a LED Red glass.
Show Message When Recording Starts: You can disable the poster recording has begun.
Load Length Of Movies In Movielist: It shows the duration of events
Show Positioner Movement: If you activate this option when changing satellites or move the motor will see an icon on the screen telling us that the engine is moving.
Enable Multiple Bouquets: If you use multiple lists Bouquets channels have to have this option activated
Multi-EGP Bouquets Selection: You can activate this option to see a full EGP each Bouquets
Change In QuickZap Bouquets: When using multiple lists with multiple Bouquets, Bouquets at the end of each back to the beginning of the same Bouquets, if you want the end of your jump to the next Bouquets Bouquets automatically, activate this option.
Alternative Radio Mode: unknown to me
Action On Long PoweButton Press: We can change the configuration of the Power button on the remote when you press more than 5s
- Show ShutDown Menu
- ShutDown Now
- Stanby
Action On Short PoweButton Press: Same as above but clicking once
- Show ShutDown Menu
- ShutDown Now
- Stanby