Ok first I use tftpd32 server for Windows,link to download hxxp://tftpd32.jounin.net/.
I put vmlinux.bin(from first link) file where is main tftp exe file is, and after start of the program just change "Current Directory" to point
there if allready not and change "Server interface" to your PC IP Address(mine is 192.168.1.3) and let it stay running.
Thats all to setup tftp on Windows.



Next, boot up receiver and transfer all files from second link in
/MMP/modules/2.6.22/ (make 2.6.22 folder)

chmod 755 all files

Pls make shure you have this files on DISK1 because I am using this files.
/DISK1/.passwd
/DISK1/.shadow




Next, download MMP uClibc tmp folder from third link.You must unpack it on receiver because of soft symlinks.
After extract you should have /MMP/tmp folder with uClibc based librarys files.We need uCLibc because of setting up video signal out with
small MRUA app.




SO, after this go into telnet console and write this command (ELITE MODEL tested!!!!!)

setxenv -f /dev/mtdblock0

it should list all XENV settings in flash. Our main interest for now is in 4 settings,

y.ipaddr,y.subnetmask,y.gateway and y.start,

unfortunaly YAMON boot loader doesnt have dhcp so you must manualy add all IP based datas.Pls be cerful with this, if you are wrong with this settings you will not be able to boot and no other way to repair

it, then to make your self rs232 cable like "telesat" user explain here.

So before you change pls write down default values for this 4 settings but main value y.start IS MUST so you can change it back after you want to load standard FW!!!!

Here is my values for IP datas. My router always give my Azbox receiver this IP address 192.168.1.5, Subnet mask for this range is 255.255.255.0 and my router gateway is 192.168.1.1.
So this is way I will change this values for mine IP settings


(It takes few seconds to change value)
setxenv -f /dev/mtdblock0 -k y.ipaddr -v "192.168.1.5"
setxenv -f /dev/mtdblock0 -k y.subnetmask -v "255.255.255.0"
setxenv -f /dev/mtdblock0 -k y.gateway -v "192.168.1.1"

-------------------------------

Next is to change boot up command for Yamon, default value on my receiver is

y.start on my receiver is "xrpc 0xac080090; load zbf 0xb3000000; go"

so pls write it down somewhere.


So, next step is to change startup boot command (y.start).
PLEASE CHANGE IP ADDRESS FOR YOUR TFTP SERVER, MINE TFTP SERVER PROGRAM IS ON PC(WINDOWS) WITH 192.168.1.3 IP ADDRESS!!!!!!!!!!!!!!!!!!!!!!!!!!



setxenv -f /dev/mtdblock0 -k y.start -v "net init; net initpci; net up; load -b tftp://192.168.1.3/vmlinux.bin 0***020000; go"
hmm 0x 9 0 0 2 0 0 0 0 ,just put it together instead of 0***020000 and without spaces!!!


after you change all just in case ./setxenv -f /dev/mtdblock0 check again if your values are okey,plus y.XXXX commands maybe some letter is missing while you type it!!!!!


It's just left to boot it, so type reboot in console and hope it will boot







to go back after boot to standard firmware, go to /MMP/modules/2.6.22 , where setxenv program is and put back OLD y.start command value and just reboot it

./setxenv -f /dev/mtdblock0 -k y.start -v "xrpc 0xac080090; load zbf 0xb3000000; go"

-----------------------------------------------------------

If all goes well you should be able to telnet/ftp to Azbox receiver.If NO, sorry I dont have solution, you will need rs232 cable to fix it,
But if all okey, telnet and go to /MMP/modules/2.6.22 folder and use set_outport prog to activate video out signal, I just tested analog out

./set_outport -analog -f PAL_BG


for digital maybe this way

./set_outports -digital -f HDMI_1080i59 -dvi_hdmi siI9030 -hdmi2c 2



If anyone managed to come till here I will explain how to load FB driver, it's still in working process and it has fixed screen resolution 720x576, and maybe
letter upload E2 files but it needs alot of patching and fixing plus writing next driver(s).

Sta je novo ?

- Rade SD i HD FTA Kanali ( Testiran Dolby Digital 2.0 i AC3 preko HDMI , kanal Einsfestival HD ).

- Poboljsana podrska za sekcijske filtere i PID selekciju.

- Novi IR driver ( mapirano par novih tastera sa daljinskog, npr. Info button, Audio button je check button na upravljacu ).

- Dodat dio CA sistema ( Uskoro cete moci koristiti sve nativne CAM-ove od DreamBox 8xxx , 500 HD )

- Multimedia podrska za MPEG 2 , MPEG 4 ( XviD ), H264 i druge formate kako video tako i audio ( Veci broj formata ce biti podrzan naknadno ).

- Procitajte ReadMe file, za vise informacija kako instalirati tri plugina da Vam ide Multimedia preko E2 Media Playera .


Read Me za Multimediju :

If You want also to test Multimedia on AzBox Enigma 2 media player , You have to install 3 IPK files located in this archive :

gst-plugin-asf_0.10.16-r0.0_mipsel.ipk

gst-plugin-avi_0.10.25-r0.0_mipsel.ipk

gst-plugin-dvbmediasink-dbg_0.10+cvs20101006-r0_dm800.ipk

working formats:
audio: mpeg, aac, ac3, dts, wma (but not pro), pcm (not all ?)
video: mpeg2, mpeg4 (xvid), h264 (only show singe frames)

IPK Installation procedure :

Transfer 3 *.ilk files to /tmp folder of Your AzBox and run this commands, one by one :


ipkg install /tmp/gst-plugin-asf_0.10.16-r0.0_mipsel.ipk

ipkg install /tmp/gst-plugin-avi_0.10.25-r0.0_mipsel.ipk

ipkg install /tmp/gst-plugin-dvbmediasink-dbg_0.10+cvs20101006-r0_dm800.ipk


If You cant use ipkg install, use command opkg install or ipkg-extract .




Uskoro ide i driver za Premium+ resiver ( u toku je testiranje ).

If You see error while nstalling .ipk files, that is ok, dont worry about it, but dont forgett to transfer 2 .so files attached to my post in addons.zip archive to directory :

/usr/lib/gstreamer-0.10