DreamUP Patched dm800 clone

[antox]

DreamUP Patched dm800 clone
DreamUP Patched dm800 clone

No ca found by 2nd stage loader
This can be done in 2 ways.
1) You have to have a working dreambox.
2) DM800_repair, you alter dreamup to be able to use greyed buttons.
Now for the first sollution.
1) Connect working dreambox DM600/DM800.
2) Open dreamup, press connect.
3) When dreambox is found by dreamup, insert Null-Modem cable in
the broken dreambox.
4) Press flash button, and chose a firmware.
5) The flash progress will probably hang, its OK.
6) Open dreamup again, connect the broken box, press connect.
7) If all went ok, you can now flash box again, (Use only serial
communication)
Now for the second sollution
1) Connect broken dreambox DM600/DM800
2) Open dreamup, press connect.
3) When you see second loader error popup, just press ok.
4) Open
5) Drag DM800_repair in front of dreamup, and press dream multimedia logo.
6) Now press the greyed Flash button, and chose firmware.
7) The flash progress will probably hang, its OK.
Open dreamup again, connect the broken box, press connect.
9) If all went ok, you can now flash box again, (Use only serial
communication)

how to and picture PDF files is inside of the zip folder

[antox]

DreamUP Patched DM 800 clone
DreamUP Patched DM 800 clon

16-05-2010

Gracias a forhike & natas

[antox]

dream up patched dm800 clone
This includes Enforcer and manual how to fix 2nd stage loader error.

[martytay]

When I try to load firmware it says 'file to big' what should I be flashing?

[antox]

Set alata za popravku DM800HD
Nova revizija alata za popravku DM800HD - Kineza
Koristiti isključivo ovaj doradjeni DreamUP



how to use enforcer: varijanta

1) connect dead box to dreamup, press connect
2) press ok at ca error popup, any error just press ok
3) download enforcer
4) drag enfocer in front om dreamup, press enable in enforcer
5)press flash and chose flash file
6) flash probably hangs
7) connect the broken box to dreamup, press connect and try flash, chose flash file, hopefully it works now



To explain all qestion about file to big!!


1. switch on enforcer press enable
2. Run dream up and press connection
3. Switch on dm800 (should send now BL to box)
4. If dreamup succesfully send BL to box (doing this automaticly when you plug in power cable to box)
5. shout down dream up and enforcer
6. shout down box, switch on dream up (just dream up! press connection)
7. switch on box
8. now when everything goes ok, you are able again to flash box

IMPORTANT, enforcer just help get connection when dream up cannot connect to box.
Package for repair dm800

DM800HD repair koji zamjenjuje Enforcer

"No CA found by 2nd loader", neznam koliko je vlasnika DM800, DM8000 dobilo ovu poruku, a onda su svoj DB morali poslati u Njemačku na popravku, pod uvjetom da nije klon.





Nakon ove poruke DB800 je potpuno mrtav, nema sa boxom kontakta ni via comporta ili LAN-a.

Čisto tehnički treba ga direktno flshat sa DreamUp, pod uvjetom da se preskoči stupanj u DreamUp-u simuliranjem repair winhex i tako izmanipulira DreamUp on the run.

1. Priključi ispravan DB800 i klikni connect na DreamUp-u
2. Prebaci kabel na ubijeni DM800 i klikni flash
3. Pokvareni DM800 će zablokirati, ponovo ga connect
u DreamUp-u, nema poruke "No CA Found by 2nd
loader" zatim klikni flash i nakon 45 minuta novi
image je unutra i ispravan DM800.

Da bi sve išlo jednostavnije tu je usložen "Enforcer",
jednostavan alat koji manipulira DreamUp u on the run.
Jednostavno mrtvi DM800 treba spojiti cablom, na Enfoceru kliknuti enable, zatim na Pachiranom DreamUp-u connect, odabrati image te kliknuti flash. Za 45 minuta imate ispravan DM800 bez Njemačke.

a. Enforcer
b. Nabrijani DreamUp

[azizan8]

Thanks for your method. It seems work but I am still stuck due to "file too big". I search everywhere however still no solution yet. Can anyone help me on this?

[ojdafuks]

neide pa neide