Mini U-boot-r1.1 final for UFS910
Installation manual:
Download and unzip the attachment erstmal.
HyperTerminal and kermit are a possibility:
Box turning and stopping in the HyperTerminal on the console and then booting eintippeln on Promt STB7100-ref> following line and press <enter> taste:
loadb a4000000
in the HyperTerminal on "Transfer / click on the Send File", and miniUPDATE.img kermit-mode select and send. When the transfer is finished, type in the console forward those 3 lines and confirm each with <enter> taste.
Please take care to meticulously Tppfehler:
A0030000 protect A003FFFF off
erase A0030000 A003FFFF
cp.b A4000000 A0030000 10,000
ready ... n few seconds after turning box and again.
Innovations in brief:
compatible with the existing mini-bootargs
The variable-bootargs Bootmenuteimeout falls away completely
new variable-bootargs bootdesc_default with numerical value 0-9 contents
will boxstart during the bootdesc_default performed within 0.3 sec,
But if you want to pick something else, then we must simply with the arrow up / down button and hold boxstart order is then adjusted 10sec timeout and you have enough time to choose from.
To change the bootdesc_default too must first be held at Boxstart Pfeilup / down button is pressed, so that the timeout is set to 10sec. Now bring the desired selection in the display and the <FAV> key press and hold about 3 sec) (until "saving" by default. The selection is saved for the next Boxstart as default and the image started directly.
-bootconf-repair
When times are gone and bootargs garnix more passes (for example, "Warning: bad CRC, using default"): r.1 while the mini is still in its place in the flash it can be run via the serial console with "Bootmen A0030000"
Then you have to ... restarted simply do nothing and wait until the box has 2 times.
Then is then:
the bootargssektor repaired
ipaddr = 192.168.178.77
serverip = 192.168.178.1
GatewayIP = 192.168.178.1
netmask = 255.255.255.0
ethaddr = 00:50: fd: ff: 12:34
bootcmd = Bootmen a0030000
With these default settings, even a (not yet destroyed) image is back to normal start.
If the image should also be broken, so now at least back to KCC or access over the network because all the hardware required bootargs been restored.
emergency_boot:
In Rev1.0 that was not there. Is now again fully operational, the Menutaste the device must be only about 2 sec longer pressed.
direct flashing with mini:
if one of nem on an internal SATA or USB stick or on a full-nem TFTPserver image with names
miniFLASH.img
test (size 15.8 MB) and the Boxstart the REC button is pressed holds approximately 3 seconds (until "FLASH mini search" in the display) appears, then the miniFLASH.img searched in the media. Once it is found, it is loaded and flashed. FAT32 or ext2 does not matter on the stick ... miniFLASH.img has only the root of the partition are FIRST, then 0:1 to USB or IDE 0:1. Even the usually used as a swap device on the USB stick is suitable. Here, then in the subdirectory / images / after miniFLASH.img sought.
mini disable:
hold down Boxstart Exit ", then that becomes bootcmd set back to original" Bootmen a0040000. This makes the mini "out there"
This version should also work together with existing BAinstallationen and can also be used with the current e2BA 0.33. To a lesser extent changing operation. If there is something still not right, then please
1. not being angry and
2. Items so that we can adjust the
