« previous next »
Pages: [1]   Go Down

Author Topic: Amiko SHD-8900 ALIEN/Enigma  (Read 19827 times)

0 Members and 1 Guest are viewing this topic.

Offline antox

  • Ferengi
  • Global Moderator
  • Hero Member
  • *****
  • Posts: 16798
Amiko SHD-8900 ALIEN/Enigma
« on: January 11, 2011, 11:46:28 AM »
RSP Enigma Installation


- U need 1 FAT32 formated USB
- create one folder named /enigma2
- Power OFF the receiver from the back switch
- plug in the USB
- press the OK button on the front panel and power ON the receiver
- hold the OK button till on the display you will see the following message:
 FORC ( forced boot )
- press "down" ( V ) button and on the display, you will see "ENIG" message now press OK
- power OFF the receiver, press "OK"and power ON again
- after the FORC message appear press "right" ( > ) and wait till the upgrade is complete
Logged

Offline toogood

  • Jr. Member
  • **
  • Posts: 11
Re: Amiko SHD-8900 ALIEN/Enigma
« Reply #1 on: January 15, 2011, 10:56:55 AM »
napise 7 70 i broj 70 mi blinka na displeju i tako stoji....jel to ok?
Logged

Offline antox

  • Ferengi
  • Global Moderator
  • Hero Member
  • *****
  • Posts: 16798
Re: Amiko SHD-8900 ALIEN/Enigma
« Reply #2 on: February 14, 2011, 07:00:56 PM »
How to First Enigma 2 image for Amiko Allien spark STI7111

  HOW TO INSTALL
  I'm going to as a description of the installation procedure ... something special
  right to read this material!

  Installing Enigma2 RSP is a special type that refers to a whole
  Flash partition and not the components. The installation procedure requires activation
  how "emergency boot" as follows:

  - you need a stick
  - create a FAT32 stick containing the installation directory / Enigma2
  - switch off the handset from the network
  - insert pad
  - Click OK on the front panel and hold it in place while under stress
  - Display screen appears Force (forced boot)
  - click the down arrow (V) will appear on the screen and then click OK ENIG
  - Switch off the receiver from the power and press OK again and rekindled
  - press the right arrow (>) and wait for the upgrade operation

  The restart will take a picture Enigma2 elements requiring configuration ...

  To be "light" after taking the RSP's Panell (you can find the red key), and oscam oscam config, edit oscam.conf.
  In / var / keys / oscam.conf boxtype put the device type:
  [dvbapi]
  enabled = 1
  have = 1
  boxtype = dreambox

  Lines to keep them in / var / keys / oscam.server.


  E2 go at the USB readers (Smartmouse, Smargo etc.) will become active reader in the following figure.

Logged

Offline antox

  • Ferengi
  • Global Moderator
  • Hero Member
  • *****
  • Posts: 16798
Re: Amiko SHD-8900 ALIEN/Enigma
« Reply #3 on: February 14, 2011, 07:02:47 PM »
Download function introduce

  Menu "download"
  In main menu, choose download icon and press [ENTER] to enter to download menu.

  Browse server
  button use to switch among browse server, downloading list and downloaded list.
  button use to select the servers.
  [Yellow] button use to config the max number of allow download.

  Thx To vicky

Download function introduce

  Menu "download"
  In main menu, choose download icon and press [ENTER] to enter to download menu.

  Browse server
  button use to switch among browse server, downloading list and downloaded list.
  button use to select the servers.
  [Yellow] button use to config the max number of allow download.

  When you enter to “browse server/server list” menu, you will see a screen like below:
  Press
button to select connect icon, and press [ENTER] button to connect the server that you select.
  Press
and [up/down] buttons to select add icon, and press [ENTER] button to enter to add server menu. And do next
  Press
and [up/down] buttons to select delete icon, and press [ENTER] button to delete the server that you select
  Press
and [up/down] buttons to select edit icon, and press [ENTER] button to edit the server that you select, and then do next.

  When you enter to “browse server /file list ” menu, you will see a screen like below:
  Press
button to select disconnect icon, and press [ENTER] button to disconnect the server.
  Press
and [up/down] buttons to select refresh icon, and press [ENTER] button to refresh the file list.
  Press
and [up/down] buttons to select download icon, and press [ENTER] button to enter to "information" menu, then do next and press button to confirm.
  Press [info] button or press
and [up/down] buttons to select info icon, and press [ENTER] button to display the information of the file that highlight


Logged

Offline antox

  • Ferengi
  • Global Moderator
  • Hero Member
  • *****
  • Posts: 16798
Re: Amiko SHD-8900 ALIEN/Enigma
« Reply #4 on: February 14, 2011, 07:03:34 PM »
How to Upgrade plugin by FTP
Quote
 Upgrade Step:
  1. Set your STB IP addr in system/Net setting menu
  2.connect your PC to STB by LAN, now we only support LAN, do not support WLAN
  3.Use ftp to telnet stb and copy plugin folder to /root

Upgrade Spark7111 by USB
Quote
Preparation:
  1. We only recommend Kingston USB stick, we don’t support USB hard disk
  2. Please make sure your USB stick only have 1 partition and the file system is
  FAT32
  3. Set default booting system to [spark].

  Upgrade Step:

  1. Make sure [C:/spark] is exist, if not, please create this folder.
  2. copy [mImage] and [userfsub.img] to [C:/spark]
  3. Connect USB stick to STB
  4. Keep Pressing [OK] Button in Front Panel, then power on STB.
  5. After 5 seconds, you will see [Forc] in LED, release [OK] button and press
 
Button.
  6. if everything OK, You will see [U LD] shining in LED
  7. if upgrade success, You will see [SUCC] and STB reboot automatically
  8. If upgrade not finishes in 5 minutes, then there must be something wrong, please
  check your configuration and re-try.


Upgrade Spark by TFTP
Quote
Since we have some restrictions and can not support all kinds of USB stick, we
provide another option (TFTP) to upgrade Enigma2/Spark.
Preparation:
1. Install TFTP tools [csicotftp11.rar] to your PC
2. Set your PC IP addr to [192.168.40.19]
3. connect your PC to STB by LAN, now we only support LAN, do not support WLAN
4. Set default booting system to [spark]
Upgrade Step:
1. copy [mImage] and [userfsub.img] to any folder of your PC, for example [C:/spark]
3. Keep Pressing [OK] Button in Front Panel, then power on STB.
4. After 5 seconds you will see [Forc] in LED, release [OK] button and press
Button.
5. if everything OK, You will see [T LD] shining in LED and you will see some debug
information in TFTP Server, like
“ Mon Oct 25 14:02:36 2010: Sending 'mImage' file to 192.168.40.19 in binary mode
Mon Oct 25 14:02:39 2010: Successful.
Mon Oct 25 14:02:50 2010: Sending 'userfsub.img' file to 192.168.40.19 in binary
mode
Mon Oct 25 14:03:33 2010: Successful.”
6. if upgrade success, You will see [SUCC] and STB reboot automatically
If upgrade not finishes in 5 minutes, then there must be something wrong, please
check your configuration and re-try.
How to Upgrade Uboot by RS232

 
Quote
 Preparation:
  1. Open [HyperTerminal] and set default parameters
  Symbol rate: [1152000]
  Data bits: [8]
  Parity: [None]
  Stop Bits: [1]
  Data Flow Control: [None]
  2. Select [Transfer/File Transfer] Option
  3. Select [u-boot.bin] and use [Ymodem] Option, send file
  Upgrade Step:
  1. Keep Pressing [OK] Button in Front Panel, then power on STB.
  2. After 5 seconds you will see [Forc] in LED, release [OK] button and press
 Button.
  3. If everything is ok, in STB you will see [LOAD] shinning in LED.
Spark7111 Upgrade Guide- Application
Quote
 Functions Overview
  In SPARK7111 Application, we can:
  􀁺 Upgrade Spark Dbase, System can recover if power down
  􀁺 Upgrade Spark Application, System can recover if power down
  􀁺 Upgrade Spark Application+Dbase, System can recover if power down
  􀁺 Upgrade Spark whole system (hidden),System can NOT recover if power down

  3.2 Upgrade Option [Dbase]
  Upgrade [Dbase] Option only includes channel list, Tp list, Satellite List.
  Do not include User Preference Data (STB IP, default language etc)


  3.3 Upgrade Option [App]
  Upgrade [App] Option only includes Application code. Do not include Dbase or User
  preference data.


  3.4 Upgrade Option [App+Dbase]
  Upgrade [App+Dbase] Option only includes Application code, Dbase and User
  preference data.


  3.5 Upgrade Option [System]
  Upgrade [System] Option includes all spark system as well as uboot.
  Upgrade Step:
  1. Enter into Upgrade menu
  2. Select Upgrade package
  3. Press [EPG],[5], [2], [1],
  • to activate upgrade
Logged
Pages: [1]   Go Up
« previous next »